TIPS ABOUT HOW TO Extend Smok Pen Recharge Time


TIPS ABOUT HOW TO Extend Smok Pen Recharge Time

The Smok Pen is really a new pen that was created by two guys in California. They wished to develop a cool writing instrument that appeared as if a real pen but had the ability to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has taken the marketplace by storm.

smok pen

The Smok Pen includes a built quality that’s just great. I found that even though it can be an electronic pen the build quality is simply as good as the pens that I’ve reviewed. This is because of how they made the most notable cap. You don’t have to be worried about the cap cracking or breaking on you Smok Vape Shop Valve Pen.

The two biggest differences that separate the Smok Valve from other pens is the form of the coils and just how that they are built. In general the coil on a Smok Pen is larger than on other pens. I believe that they did this deliberately, to make the pen feel bigger.

Invest the a look at a Smok Pen, you will notice that your body of the pen is round rather than smooth like other pens. On the trunk of the pen there is a little tab that houses the coil. Once you press on the tab it is simple to turn the heating element on / off. I must say i liked this feature since it allows me to use the Smok Pen 22 whenever I feel like smoking.

To utilize the Smok Pen you have to keep carefully the heat button pressed. Once the button is pressed, the heating element will begin to warm up. Once it gets to the appropriate temperature you can switch off the heating element. Smok recommends utilizing a 22mm tank. I prefer a larger tank, but that’s just me.

Once you put your Smok Pen into the tank you will notice a indicator light seriously. The indicator light will remain green if you don’t put your Smok Pen in to the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. It is important to always put your pen in to the charger before you apply the e-liquids to the coil heads. It is also important to do this before putting your e-liquids in to the coil heads.

After you have completed this step, it is best to check to see when you are at the right temperature for the coils to fire. Or even then you should turn the power off and try again. When you are still not satisfied together with your Smok Pen then I suggest you take it set for some troubleshooting. This is exactly what I’d call the “troubleshooting process” because sometimes things just usually do not work as they should. I suggest that you perform the next two steps, then go on and check the Smok Pen to see if it still gets the electronic charging port.

Before you go any further you should remove the battery from your pen and unscrew the magnetic cap. You should then remove the plastic sleeve that holds the sub-ohm. There is a wire that runs through the Smok’s body that is green in color. You need to loosen this wire using pliers. Once you have loosened this wire after that you can access the sub-ohm. You need to then take away the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful never to touch any of the coils.

Once you have placed the sub-ohm tank in to the pen you should then place the rest of the components like the wattage, the batteries and the heating element in to the included microwaveable microwave oven. Turn on the power and follow the on screen instructions. You should place the pen’s battery into the microwave and activate the setting. You need to then wait approximately 30 seconds before turning it back off. When you initially put the pen in to the microwave the electronic reading will show a minimal voltage protection setting. If this setting does not automatically get set then you should follow the on screen instructions.

After the Smok Pen has reached the temperature that it needs to reach you need to then connect both wires to the negative and positive on the positive post on the Smok unit. You need to then connect another end of the battery to the negative post on the negative side of the Smok unit. The final step is to connect the positive cable to underneath of the Smok’s on / off switch.

After all of the components have been placed into the pen, you should turn the energy on. Following the first test run, you have to be able to see the battery life indicator light seriously. If you don’t see any sign of life from the Smok Pen, you should take away the battery from the pen and replace it with a brand new one. For your convenience there is also a green light that may be pressed as a way to confirm the battery charging status. When you have done these things and you also do not see the green light indicating charging, you should replace the battery.